| Industrial
Ultrasonic Cleaning Systems |
|
An ultrasonic generator, ultrasonic transducer, and ultrasonic tank make up an
ultrasonic cleaning system, and Crest's systems are designed
to provide the most effective precision cleaning results.
GENESIS™
Ultrasonic GENERATORS
• Outstanding and
consistent performance, process control and the ability to monitor
output for consistent cleaning time after time.
• TRU-SWEEP™ sweep
frequency eliminates inconsistent cleaning by sweeping a +/- 1kHz
around the center frequency at a set repetitive rate.
• Standard two power
options to vary cleaning from gentle for delicate parts to periodic
short blasts of power for hard to clean parts.
• 3 controls including
Amplitude control to vary ultrasonic power, Duty Cycle Control to
control the amount of ultrasonic energy delivered and Frequency control
to adjust the frequency of the ultrasonic energy reducing audible noise
from subharmonics.
• Available in 25, 40 or
68 kHz frequencies and in either 250 or 500 watt models.
|
| |
|
Transducerized Tanks
• Provides the optimum
environment for precision cleaning with extended service life.
• Constructed of
cavitation resistant, bright annealed 316L stainless steel.
• Welded inside and out
for long-term stability and sturdy performance.
• Cove corner construction
with ground and polished welds available.
• Sloped bottoms for easy
draining.
|
| |
|
Ceramically
Enhanced Bar Transducers
These specially bonded, durable transducers offer enhanced cleaning
performance. The Ceramcially Enhanced Bar design consists of two
transducer stacks which permit simultaneous multiple frequencies. They
are available in the form of transducerized tanks and separate
immersibles which are fully sealed so they can be inserted into an
existing tank to convert it into an ultrasonic cleaning system.
|
| |
Technical Information
Genesis™ Ultrasonic Generators |
|
|
|
Model
|
Full
Wave
|
Half
Wave
|
Full
& Half
Wave
|
Max.
Power Input
120V/50-60 Hz
|
Dimensions
L x W x H
|
#
of Plug-in
Modules
|
|
G-250-3
|
250
|
125
|
500
|
3A/360W
|
5.25"x14"x12"
|
1
|
|
G-500-6
|
500
|
250
|
1000
|
5A/600W
|
5.25"x14"x12"
|
1
|
|
G-750-9
|
750
|
375
|
1500
|
8A/960W
|
10.5"x14"x12"
|
2
|
|
G-1000-12
|
1000
|
500
|
2000
|
10A/1200W
|
10.5"x14"x12"
|
2
|
|
G-1500-18
|
1500
|
750
|
3000
|
15A/1800W
|
15.75"x14"x12"
|
3
|
|
G-2000-24
|
2000
|
1000
|
4000
|
20A/2400W
|
21"x14"x12"
|
4
|
|
| |
|
NOTE: Prefix X in model
number should be substituted with a 2 (for 25 kHz) or 4 (for 40 kHz)
when ordering. Last digits in model number indicate the number of Ceramically Enhanced Bars on the unit.
STANDARD FEATURES:
Amplitude control • sweep frequency.
OPTIONS: Power intensity
control (duty cycle type) • Timer: 0-30 minutes • Other input voltages
• Nema 12 enclosure • Sealed generator (coated with heat sink) • CWF
watt frequency meter (generator mounted or remote) • Adjustable sweep
frequency • Remote power control • Single channel
computer interface (power monitor and control) • Three channel
computer interface (amplitude, duty cycle, frequency control and power
monitor).
Transducerized
Tanks
|
|
Model
|
Capacity
(Gallons)
|
Internal
Dimensions
W x L x D
|
Overall
Dimensions
W x L x H
|
Power
Req.
(heated tank)
|
Generator
Required
|
|
HT-710-3
|
3
|
7"x10"x10"
|
10"x13"x14.5"
|
120V/4.2A/500W
|
250W
|
|
HT-1014-6
|
5
|
10"x14"x10"
|
13"x17"x14.5"
|
120V/8.4A/1000W
|
500W
|
|
HT-1218-9
|
10
|
12"x18"x12"
|
15"x21"x16.25"
|
240V/8.4A/2000W
|
750W
|
|
HT-1524-12
|
19
|
15"x24"x14"
|
18"x27"x18.75"
|
240V/12.6A/3000W
|
1000W
|
|
HT-1622-12
|
22
|
16"x22"x16"
|
19"x25"x20.75"
|
240V/12.6A/3000W
|
1000W
|
|
HT-1826-18
|
33
|
18"x26"x18"
|
21"x29"x22.75"
|
240V/16.8A/4000W
|
1500W
|
|
HT-2426-30
|
49
|
24"x26"x20"
|
27"x29"x24"
|
240V/21A/5000W
|
2500W
|
|
HT-2436-42
|
68
|
24"x36"x20"
|
27"x39"x24"
|
240V/34A/8000W
|
3500W
|
|
HT-2446-54
|
86
|
24"x46"x20"
|
27"x49"x24"
|
240V/42A/10,000W
|
4500W
|
|
HT-1236-24
|
34
|
12"x36"x20"
|
15"x39"x24"
|
240V/17A/4000W
|
2000W
|
|
HT-1246-30
|
43
|
12"x46"x20"
|
15"x49"x24"
|
240V/21A/5000W
|
2500W
|
|
| |
|
NOTE: All tanks have 1"
wide flange around top edge. Flange not included in overall dimensions.
Prefix X in model number should be substituted with a 2 (for 25 kHz) or
4 (for 40 kHz) when ordering.
OPTIONS: Stainless steel
tank cover • stainless steel work basket • water jacket • condensing
collar • overflow well • cove corner construction
• ground and polished welds • drain valve - ball type (brass
or stainless steel) • recirculating filter system (brass or stainless
steel) • matching rinse tank - no transducers (heated or
unheated) • ChemCrest chemicals • custom sizes •
sealed skirts • different voltages • sound dampening.
Immersible
Transducers
|
|
Model*
|
Mounting
Types
Available*
|
Dimensions
W x L x H**
|
Generator
Required
|
|
CI-320-3
|
FC,
EB, DBB
|
3.5"x20"x3"
|
250W
|
|
CI-710-3
|
FC,
EB, BB
|
7"x10"x3"
|
250W
|
|
CI-720-6
|
FC,
EB, DBB
|
7"x20"x3"
|
500W
|
|
CI-817-6
|
FC,
EB, DBB
|
8"x17"x3"
|
500W
|
|
CI-1218-12
|
FC,
DBB
|
12"x18"x3"
|
1000W
|
|
CI-732-12
|
FC,
DBB
|
7"x32"x3"
|
1000W
|
|
| |
|
* When ordering, add
mounting type desired as model suffix (e.g. 4CI-710-3-EB)
** Height listed is for 40 kHz. Height for 25 kHz is 4 ".
NOTE: Prefix X in model
number should be substituted with a 2 (for 25 kHz) or 4 (for 40 kHz)
when ordering.
OPTIONS: Titanium nitride
coating • custom sizes.
|
| |
| Download The Generator Repair Form |
| |
| |
| |
